MANUAL FURUNO FCV 600L FULL
The Furuno FCV587 is fitted with a color LCD screen that measures nearly 7-inches high and full 5-inches wide on the diagonal I measured it at 8.4-inches. Unfortunately there is no NMEA2000 capability built into this fishfinder.
This unit can interface with NMEA 0183 devices using wiring that is part of the power cable. Twist-lock ports on the case back allow for quick and easy connection of both the power and transducer cables. I flush mounted the display unit using the provided hardware since it will participate in a long-term review going forward.
I set things up by selecting the proper transducer from a list provided on the display menu. They run the gamut from a 600-watt plastic transom-mount with built-in water temperature sensing to a 1000-watt bronze thru-hull with water temperature and speed sensors. Several transducer options are available for the Furuno FCV587. The only additional component needed for full functionality is a transducer. The display unit contains all the required electronics needed.
MANUAL FURUNO FCV 600L PLUS
The package shipped to us containing the display unit, power cable, operator’s manual, a 1-page plasticized card operator’s guide in English as well as 14 other languages, a beefy tilt and swivel mounting bracket, hardware to mount the bracket, plus a template and hardware to flush mount the display unit. This display is useful for comparing the same picture with two different frequencies.The Furuno FCV587 display unit measures 9.2 inches wide by 9.2 inches high with a depth of 4.2 inches. The 50 kHz picture appears on the left the 200 kHz picture on the right. For this reason the 200 kHz frequency is ideal for detailed observation of fish schools. The higher the frequency of the ultrasonic signal, the better the resolution. Therefore, the 50 kHz frequency is useful for general detection and judging bottom condition. The lower the frequency of the signal, the wider the detection area. The sounder uses ultrasonic signals to detect bottom conditions.
The screen you chose appears soon thereafter. Rotate the MODE knob again to choose the display mode desired. Rotate the MODE knob to open the mode setting window, which is displayed for five seconds.Ģ. (The start up screen appears with the maximum brilliance.) Adjust the brilliance as necessary. Note: When the power is reapplied after turning off the equipment with minimum brilliance, minimum brilliance will be set after the equipment goes through its initial start up. Press the ENTER key to save the setting and close the window. “0” is the lowest and “9” is the highest.Ĥ. To adjust contrast, after selecting “Contrast" by using S or T, use W or X (only for FCV620). “0” is the dimmest and “9” is the brightest.Īfter selecting “Brill” by using S or T, you may also use W or X to adjust brilliance.ģ. To adjust brilliance, press the /BRILL key.Ĭontinual pressing changes the brilliance continuously (0 →1 →. (The FCV-585 does not have the contrast function.)Ģ. Press the /BRILL key momentarily to show the contrast/brilliance adjustment window. When this occurs, press the MENU/ESC key twice to close the menu.ġ.3 Adjusting Display Contrast and Brillianceġ. Note2: The first time you turn on the power (or any time the power is applied after a memory reset), the installation menu appears. However, the equipment may not work properly. Note1: If "ROM/RAM check error!" appears, try to press any key except the /BRILL key to start operation. The time remaining until power is turned off is counted down on the screen. To turn off the power, press the /BRILL key more than three seconds. After the completion of the equipment check, the last-used display appears.Ģ. The unit beeps, the startup screen appears, and then the equipment checks the ROM and RAM for proper operation. Press the /BRILL key to turn on the power. ġ.13Erasing Weak Echoes.ġ.14A-Scope Display.ġ.15Fish Information. Shifting Range.ġ.11Suppressing Interference.
0 kommentar(er)
